NEW Vesion of Bolting Torque Now available
چکیده : ( توضیح در مورد یک نرم افزار )
یکی از مهمترین دلایل ایجاد نشتی در اتصالات فلنجی صنایع نفت و گاز و پتروشیمی و خطوط لوله ، عدم رعایت رویه مربوط به سفت کردن پیچ های فلنج می باشد . یکی از پارامترهای مهم این رویه ، سفت کردن پیچ با گشتاور مناسب می باشد که مقدار آن با تغییر شرایط ، متفاوت خواهد بود . اصولاً میزان گشتاور لازم برای بستن پیچ های فلنج به عوامل مختلفی بستگی دارد که بطور خلاصه می توان به موارد زیر اشاره نمود :
- فشار فرایند: سطح مقطع پیچ باید نیروی حاصل از این فشار را تحمل نماید.
- دمای فرایند : با توجه به اینکه مقدار تنش های مجاز وارد بر پیچ به دما بستگی دارد ، دمای فرایند در محاسبات تاثیر مستقیم دارد.
- نوع گسکت : ساختمان گسکت در محاسبات مربوط به میزان سطح آب بندی استفاده می شود و داده های متریال گسکت نیز جهت اطمینان از مقاومت آن در مقابل تنش های اعمال شده و جلوگیری از لهیدگی گسکت مهم می باشد.
- نوع پیچ : ابعاد پیچ ( سطح مقطع ، مشخصات رزوه ها و طول ) جهت محاسبه نیروی وارد شده بر پیچ و متریال آن جهت تعیین حداکثر تنش مجاز پیچ مورد استفاده قرار می گیرد .
دلایل زیادی جهت لزوم رعایت گشتاور مناسب برای سفت کردن پیچ ( BOLTING ) وجود دارد که در زیر به چند مورد اشاره می شود :
- اگر پیچ ها با گشتاور کمتر از Min. Required Torque سفت شوند ، اتصال مربوطه آب بندی نخواهد شد.
- اگر پیچ ها با گشتاور بیشتر از Max. Allowable Torque سفت شوند ، مشکلاتی مانند خراب شدن رزوه های پیچ ، خراب شدن Seat فلنج ، خطر بریدن پیچ های فلنج و ... ممکن است بوجود بیاید.
توضیحات فوق ما را بیشتر به اهمیت رعایت گشتاور مناسب جهت سفت کردن پیچ آگاه می سازد .
نرم افزار حاضر مقدار مناسب گشتاور جهت سفت کردن پیچ های اتصالات فلنجی را در محدوده وسیعی از انواع متریال پیچ و گسکت و شرایط مختلف فرایندی ارائه می دهد .
داده های مربوط به متغیرهای محاسباتی از جداول و نمودارهای استاندارد های ASME , API ,ASTM استخراج و بر اساس داده های مختلف ورودی ( نوع پیچ ، نوع گسکت و اطلاعات فرایندی ) طبقه بندی شده و برای هر شرایطی ، از فرمولها و روابط مناسب استفاده می شود.
پیغام های موجود در محیط نرم افزار ، کاربر را جهت انتخاب مناسب گسکت و پیچ راهنمایی می کند .
این نــــرم افزار در محــــــیط Visual Basic نوشته شده و از بانک داده ای متنی ( DAT: TEXT Data ) استفاده می کند . حجم نصب شده این نرم افزار در حدود 2.5 MB می باشد.
استانداردهای استفاده شده در این نرم افزار :
- API 6A App. D
- ASME SECTION VIII , DIV.1 , App. A
- ASME B31.3 Process Piping
- ASME SCTION II , Part A
- ASME B16.5
- ASME B16.2
Abstract:
One of the most outstanding causes of the flange joints in the oil, gas, petrochemistry and the pipelines industries is related to the tightening procedure of the flange bolt.
One of the important parameters is a suitable torque of the bolt tightening whose amount varies in compliance of the conditions.
The various factors of the reg. bolting torque are as follows:
1- Process pressure: the bolt’s cross-section must be able to tolerate the outcome force of this pressure.
2- Process temperature: this temperature has direct effect on the calculations, due to this fact that the allowable stress amount depends on temperature when is exerted on the bolt.
3- Gasket type: the gasket type structure is used for the gasket seating or sealing calculations .the data of it’s resistance against the tensions shocking and the prevention of the gasket decay.
4- Bolt type: the bolt dimensions such as the cross-section, the threads, spec. and its length, are used for the calculation of the exerted force on the bolt, material and consequent determining of the maximum allowable tension.
Some reasons of many for the consideration of suitable thread of bolting:
1- Less than the minimum required torque bolting ends in a fitting without sealing.
2- Bolting more than the maximum allowable torque brings problems such as the threads damage, flange seat damage and hazard of the flange breakage.
The information descriptions above obligate us & much more consideration of the proper torque while bolting.
The existing software presents the suitable amount of torque which is necessary in vast range for the bolts of various materials and gaskets, under different conditions.
The calculating variables data are extracted from the ASME, API tables and diagrams are classified according to the inputting data variation such as: the bolt type, gasket type, and process information.
Include the related proper formula and relations are used accordingly. In addition the accessible messages of this software guide the user to choose any proper gasket and bolt.
This software programmed in Visual Basic and used a simple text database, this software can be installed with about a capacity of 2.5 MB.
Used standards & Codes for calculation :
- API 6A App. D
- ASME SECTION VIII , DIV.1 , App. A
- ASME B31.3 Process Piping
- ASME SCTION II , Part A
- ASME B16.5
- ASME B16.2
Distribution :
- This Software is freeware, but the copyright remains the property of the author.
You may use the software freely for personal or commercial use.
با سلام خدمت دوستان گرامی